Products
Product lines organized by supply format
The same alloy family can be supplied as strips, foils, rods, wires, or tubes. Slitting and leveling are offered as process services, while nickel-based brazing filler metals support electronic brazing—ensuring a seamless delivery path across all formats.
- Include foil thickness
- 0.0025 – 10 mm
- with foil width
- 0.3 – 1200 mm
- Bar and rod pipe diameter
- Ø0.05 – 100 mm

Precision Strip and Foil
Cold-rolled strip and foil
A full range of strip and foil products centered on precision cold rolling, with thicknesses as thin as 0.0025mm and widths customized to slit requirements.
- Thickness range
- 0.0025 – 10 mm
- Width Range
- 0.5 – 1200 mm
- Supply Status
- Soft / Cold-worked / Aged
- Surface
- Bright / Pickled / Polished
- Thickness tolerance is controlled by grade and width range; can be negotiated per drawing.
- Supports edge quality and burr height requirements
- Supplied in coils, fixed lengths, or slit strips

Wire · Bar · Tube
Rods, wires & tubes
Bars, wires, and tubes with diameters Ø0.05–100 mm share the same alloy grade system as strips, enabling multi-form procurement within a single project.
- Diameter range
- Ø0.05 – 100 mm
- Supply Format
- Coiled / Straight Bar / Fixed-Length Pipe
- Surface
- Polished / Turned / Pickled
- Status
- Annealing / Cold Drawing / Aging
- Fine-gauge wire for precision winding and electrodes.
- Bar ends can be chamfered and marked as required.
- Pipe wall thickness and concentricity shall be as agreed in the order.

Slitting
Slitting
Slit wide coils into narrow strips with clean edges and consistent widths, optimized for continuous stamping and automated production lines.
- Minimum Width
- 0.5 mm
- Incoming material width
- ≤ 1200 mm
- Collection method
- Single / Multiple Rolls / Paper or Plastic Core
- Edge
- Sheared Edge / Disk Shear
- Split by customer roll weight and diameter
- Record width and length per roll after slitting
- Can be continuously scheduled with the cold rolling process.

Stress bending straightening
Stress relief leveling
Eliminate residual stress and flatness defects in strip material through multi-roll leveling to improve planarity and enhance stability for subsequent stamping.
- Applicable Thickness
- 0.02 – 6 mm
- Flatness
- Edge wave / Mid-wave / Cupping improvement
- Residual Stress
- Control by process parameters
- Detect
- Flatness Spot Check + Record
- Straightening parameters are set separately by grade and hardness.
- Can be integrated in series with slitting and cleaning processes.
- Shipment: Plate Shape and Dimensions Record

Welding Materials
Nickel-based brazing alloys
Nickel-based brazing and welding materials for electronics, supplied as strips, foils, and wires for vacuum and protective atmosphere brazing.
- Grade System
- BNi-2 / BNi-5 / BNi-7, etc.
- Supply Format
- Strip / Foil / Wire
- Foil Thickness
- 0.02 – 0.50 mm
- Brazing temperature
- Approximately 900 – 1100 °C (by grade)
- Foil strips can be die-cut into pre-formed solder pieces to reduce assembly steps.
- Suitable for vacuum brazing and protective atmosphere brazing processes
- Electronic soldering allows the filler metal grade, joint gap, and heating curve to be confirmed according to customer process requirements.
Dimensional capabilities
Size capabilities, listed first
Include foil thickness
0.0025 – 10 mm
with foil width
0.3 – 1200 mm
Bar and rod pipe diameter
Ø0.05 – 100 mm
The above represents the standard capability range. Feasibility for specific specifications is subject to confirmation based on grade, condition, and batch size.
Tolerances
Dimensional Tolerances and Delivery Terms
Tolerance ranges vary by grade, hardness, and width. The starting values in the table below are for preliminary assessment only; final tolerances will be specified in the quote after drawing review.
| Project | Range | Reference Tolerance | Description |
|---|---|---|---|
| Thickness tolerance (strip / foil) | 0.0025 – 0.05 mm | Negotiate by grade and width | Ultra-thin specifications subject to actual process capability confirmation. |
| Thickness tolerance (strip / foil) | 0.05 – 1.00 mm | Standard range starts at ±0.005 mm | Depends on width and alloy hardness |
| Width tolerance (after slitting) | 0.5 – 1200 mm | ±0.05 mm starting from | Narrowband confirmed based on edge quality requirements. |
| Diameter Tolerance (Bar / Wire / Tube) | Ø0.05 – 100 mm | By standard or drawing | Label grinding and polishing states separately |
| Flatness (after straightening) | 0.02 – 6 mm | Agreed by length and usage | Please provide a layout diagram for the stamped parts. |
Packaging & Delivery
Coils are supplied on reels and can be slit to customer weight and diameter requirements. Foil is packed in vacuum bags with wooden crates. Rods, wires, and tubes are packaged by cut length or coil.
Shipping Documents
Shipment includes size and status records. Material composition and mechanical property test reports are provided per batch; specific items to be agreed upon upon order confirmation.
Do you have specific specifications? Please provide the dimensions directly.
Provide grade, thickness/diameter, width, and quantity. We will reply with feasibility and lead time.